Install dos on usb
- #Install dos on usb install
- #Install dos on usb software
- #Install dos on usb Pc
- #Install dos on usb download
- #Install dos on usb windows
Step 9 - Congratulations, you should see Starting MS-DOS. If you do select floppy USB, just press CTRL-ALT-DEL (soft reboot a feature thats very helpful in the DOS world) and repeat this process but ensure you select to boot from Hard USB. Make sure you dont boot from Floppy USB, since disk 3 is not a boot disk (ie you will not boot). From now on note that your boot manager will be the BIOS "boot from xxx device". When starting up, go into BIOS to select to boot from Hard USB.
(If you want to have a "floppy drive" available (highly reccomended when playing with DOS), you must boot with floppy USB inserted every time.) Allow computer 1 to reboot. At this point, DO NOT take out floppy USB from computer 1. Press Enter and wait for the installer to prompt you that the installation is compete and you must take out your floppy disks and reboot. Step 8 - Once Rufus has completed writing disk3.img to floppy USB, safely eject floppy USB from computer 2 and plug it back into computer 1 (make sure you plug it back into the same USB port as it was in at step 4 for maximum success). Now complete step 3 again but with disk3.img instead of disk1.img Step 7 - When the installer to requests you insert disk 3, take out floppy USB from computer 1 and plug it back into computer 2. Step 6 - Once Rufus has completed writing disk2.img to floppy USB, safely eject floppy USB from computer 2 and plug it back into computer 1 (make sure you plug it back into the same USB port as it was in at step 4 for maximum success). Now complete step 3 again, but with disk2.img instead of disk1.img When the installer prompts you to insert disk 2, take out floppy USB from computer 1 and plug it into computer 2. Step 5 - Follow the instructions until the installation begins. Within a few seconds, you should be in the MS-DOS installer. As it is booting, load into your BIOS and select to boot from the Floppy Drive (this is the Floppy USB). Put both Hard and Floppy USBs into computer 1. Step 4 - Once that has been completed, safely eject Floppy USB out of computer 2. Once selected, leave all other rufus settings alone and press start. Where it says boot selection, navigate to the folder you extracted the disk images to and select disk1.img. img files as they are (do not attempt to open them with WinImage.). 7z file you downloaded into a folder and leave the. If you downloaded the pack from winworldpc, unpack the.
#Install dos on usb Pc
Ensure there are no other USB sticks plugged into your pc at this point.
#Install dos on usb download
Step 2 - Download the "MS-DOS 6.22 with supplementary disk" pack from winworldpc or another source, onto computer 2 and plug in the Floppy USB. This method circumvents that by using BIOS to select which medium you wish to boot from-USB Hard Disk or your actual Hard Disk).
#Install dos on usb windows
If you want to, youre gonna have to faff around with having to reinstall windows and a boot manager.
#Install dos on usb install
Consequently, this is why we wont install onto our hard disk. This is so the DOS installer doesnt accidentally write to the first two GB of your actual hard drive (ruining your Windows/*nix installation. Step 1 - On computer 1, disconnect the hard drive from the motherboard. This will be useful once you've installed DOS for installing programs. I think you can do this with WinRAR but, I like WinImage. Rufus-For low level formatting the "Floppy USB" (the USB that will emulate the floppy disk
Ideally, you'll want the Hard USB to would be of size 2Gb or greater. You will also want two USB sticks, one you will use to emulate a floppy disk (call it Floppy USB) and one to make the hard disk on which you will install DOS (call it Hard USB). Youre gonna need two computers to make this method feasable, the computer youre installing DOS on (call it computer 1) and the computer that you will use for file transfers and formatting of the USB stick (call it computer 2).
#Install dos on usb software
Please ensure you keep IO.SYS MSDOS.SYS and COMMAND.COM however.įirstly youre gonna wanna get all the relevant software and hardware. To install onto a hard drive, the process is mostly the same.) You can also just make a boot floppy by completing step 2, then make space by deleting files you deem unnecessary and copying whatever you want onto the boot floppy. This tutorial will be for installing MS-DOS 6.22 onto a USB stick (I will explain why not to the hard drive later. I accidentally discovered this method whilst messing around about 2 years ago and have made numerous such USB sticks with much success. Please comment your thoughts and any improvements to the tutorial you might have. I recently wrote this as a comment to a post and thought it might be useful to more people that want to run DOS on real hardware.